🔥 BUY 2 OR MORE, SAVE 25%! ⚡ HD16 Plug-In CO Monitor — CO, Temperature & Humidity at a Glance ✨
🔥 BUY 2 OR MORE, SAVE 25%! ⚡ HD16 Plug-In CO Monitor — CO, Temperature & Humidity at a Glance ✨
Couldn't load pickup availability
🔥 BUY 2 OR MORE, SAVE 25%! ⚡ HD16 Plug-In CO Monitor — CO, Temperature & Humidity at a Glance ✨
🏠 HD16 6-in-1 · U.S. Plug
Plug-In CO, Gas & Smoke Monitor
One outlet. One clear view. Check your carbon monoxide reading, combustible gas and smoke status, temperature, and humidity on one color display.
Use the HD16 for supplemental indoor monitoring alongside your required household CO and smoke alarms.
Shown in black and silver-trimmed white. Screen values are example readings.
Detection Display Setup Safety Specs FAQ
🛡️ What the HD16 Checks For
🔎 Your Room Readings in One Place
Check CO in ppm, separate GAS and SMOKE indicators, plus temperature and humidity. The front display also puts the status lights in view, with a built-in buzzer and a dedicated TEST button on the unit.
📟 Read Carbon Monoxide in ppm
Carbon monoxide is invisible and odorless. The HD16 uses an electrochemical sensor with a dedicated CO / ppm readout and a display range of 0–999 ppm. If a CO alarm sounds, follow the emergency guidance below.
The cutaway illustrates the housing, display, and electronics.
💨 One GAS Indicator for Four Supported Gases
Methane, propane, n-butane, and ethane share the GAS status icon. The icon reports a shared status only. The numbered ppm field is dedicated to carbon monoxide.
The image compares common gases and vapors for education. The four gases listed above are the HD16 coverage list.
🌫️ A Dedicated SMOKE Status
An optical chamber senses changes in light caused by smoke particles and shows a separate SMOKE status. Keep required smoke alarms installed and working.
The illustration shows how particles scatter light inside an optical sensor.
📊 Get to Know the Color Display
👀 Know What Each Reading Means
In the example, 025 beside CO / ppm means 25 ppm of CO. GAS and SMOKE have separate status icons. The battery symbol shows battery status.
The screen refreshes every two seconds. Check the HD16 manual for alarm conditions and response timing.
🌡️ See Temperature and Relative Humidity
Check the thermometer for room temperature and the droplet for relative humidity. Hold the sun button to switch between °F and °C.
🔄 Turn the Readout to Suit Your Outlet
Hold the speaker button to rotate the display in 90° steps. Choose from 0°, 90°, 180°, and 270°. Press the sun button to adjust brightness.
🔌 Find the Right Outlet and Run a Test
🏠 Set Up the HD16 in Three Steps
- Choose a dry indoor spot. Check the model manual for placement and clearances before choosing an outlet.
- Plug in and check POWER. Use a compatible wall outlet with space around the monitor. Check the lights against the manual’s startup instructions.
- Run the self-test. Press TEST and check the lights and sound as directed. Then set the screen angle, brightness, and temperature unit.
Placement illustration only. Use the HD16 manual for suitable rooms, heights, and clearances.
📍 Look at the Outlet and the Space Around It
Choose a suitable location where furniture leaves the vents clear and you can see the display, read the status lights, and reach TEST.
The pictured settings are examples. Use the manual to choose a suitable indoor location.
↔️ Give the Vents Room to Breathe
Keep the case openings clear so the monitor can sample the surrounding air. Leave space around the rear vents and nearby curtains, furniture, or other objects.
🎛️ Four Buttons, Four Places to Look
- TEST · Upper left. Press to run the self-test. Check the expected lights and sound in the manual.
- Speaker · Lower left. Press to change the buzzer setting. Hold to rotate the readout. Follow the manual for the sound setting during normal use.
- Power · Upper right. When unplugged, hold to turn battery power on or off.
- Sun · Lower right. Press to adjust brightness. Hold to switch between °F and °C.
🚦 Understand the Lights and Buzzer
- 🟢 POWER. Shows the unit’s power status.
- 🟠 FAULT. Flags a fault. Use the manual’s troubleshooting instructions.
- 🔴 ALARM. Shows an alarm condition. The built-in buzzer sounds when enabled.
🔋 U.S. Wall Plug and Rechargeable Backup
This version has a U.S. two-prong plug and a built-in 1,000 mAh rechargeable backup battery. Check the product label for the outlet rating and the manual for charging and battery-mode instructions.
⚠️ Know the Risks and What to Do
The HD16 is a supplemental monitor. Keep your required, properly installed household CO and smoke alarms in working order.
If a CO alarm sounds, get everyone outside and call 911 from there. Stay outside until responders clear you to go back in.
🏡 A Room Can Look and Smell Normal
Carbon monoxide has no color or smell. A room can seem completely normal, which makes working, properly installed CO alarms important.
🔥 Recognize Common CO Sources
Fireplaces, fuel-burning water heaters, grills, generators, and vehicles can give off carbon monoxide. Use grills outdoors. Keep generators outdoors at least 20 feet from doors, windows, and vents. Keep vehicles switched off in attached garages.
🚨 Suspect a Gas Leak? Leave the Area First.
Leave immediately. Avoid using electrical switches or phones in the area. Call 911 from a safe location away from the suspected leak.
The image compares household and industrial gas settings. Follow the HD16 manual for indoor placement. U.S. gas leak guidance
❤️ Recognize Possible CO Exposure
Headache, dizziness, weakness, nausea, and trouble breathing can occur with CO exposure. Some symptoms can feel like the flu. If you suspect exposure, get everyone outside and call 911 from there.
CDC symptom guidance · CPSC emergency guidance
📋 Check the Finish, Size, and Specifications
🎨 Compare the Black and Silver-Trimmed White Finishes
See the screen from the front, the controls from the side, and the vents and U.S. plug from the back. Choose the finish that fits your space.
📏 Check the Fit Around Your Outlet
The HD16 is about 4 inches across. Use the in-hand view for scale and measure your space near furniture, a wall, or another plug. Leave the vents clear and the buttons within reach.
📝 HD16 U.S. Plug Specifications
- Model. HD16, U.S. plug version.
- CO. Electrochemical sensor with a 0–999 ppm display range.
- Combustible gas. Shared GAS status for methane, propane, n-butane, and ethane.
- Smoke. Optical sensor with a separate SMOKE indicator.
- Display. 2.8-inch IPS color screen, 240 × 320 pixels, adjustable brightness, four rotation angles, and a two-second refresh interval.
- Room readings. Temperature in °F or °C and relative humidity in %.
- Alerts and test. Built-in buzzer, POWER / FAULT / ALARM lights, and a TEST button.
- Power. U.S. two-prong wall plug and 1,000 mAh rechargeable backup battery.
- Case size. About 4 × 3.1 × 1.1 in. (W × H × D), excluding plug blades.
- Operating conditions. 14–122°F (−10 to 50°C) and 0–95% relative humidity. Use in a dry indoor location.
- Finishes shown. Black and silver-trimmed white.
💬 Quick Questions Before You Choose
Will the GAS icon tell me which gas it picked up?
All four supported gases share one GAS status icon. The numbered ppm readout measures carbon monoxide only.
Does a two-second refresh mean the alarm sounds in two seconds?
Two seconds is the display refresh interval. Check the HD16 manual for alarm conditions and response times.
What should I check when I press TEST?
Compare the lights and buzzer with the manual’s self-test instructions. The built-in test checks device operation. Sensor accuracy is a separate check.
How do I use the rechargeable backup battery?
Follow the manual for charging and battery-mode operation. When the HD16 is unplugged, hold the power button to turn battery power on or off.
Can it replace my installed CO or smoke alarms?
Keep required household CO and smoke alarms installed and working. Use the HD16 for supplemental monitoring in locations covered by its manual.
✨ Keep Your Room Readings in View
Choose your HD16 finish and check the available purchase options.